Видео

Does anyone know where the fuel filter location in 2016 is the nissan sentra??

There is no bearing in this motor, it use bushing. Bushing needs grease, not oil. Use Hi temp grease.. If your motor only humming and not spinning, then the bushing is broke or damage.

That maybe the VVTI gear

Those two Philips lamps you showed at the beginning were manufactured in August 1995. Crazy to think that those were some of the last of their kind to be sold in the US. Full-wattage F40CWs were banned from sale in the US in October 1995. Believe it or not, most of the big threes’ fluorescent lamps were manufactured in the USA up until just these past few years. It’s kind of interesting that you replaced Westinghouse lamps with Philips lamps, since Westinghouse lamps are essentially the ancestors of modern US-market Philips lamps. Philips bought Westinghouse Lighting in 1984. Subsequently, Philips-branded lamps began to be sold in the US, manufactured in Westinghouse factories. Early lamps were made on the same machinery that Westinghouse used, and featured the same black end caps that they used. Philips did sell lamps in the US before 1984, but they were branded as Norelco.

What kind of oil? Liquid wrench ok? I also have Soldier Seal Gunk Super Oil.

Is this Clark Howard? Lol

I've got an intermittent 'long crank start' issue. 'They' say to replace fuel regulator. I cant find it.

Oiled enough to get it running until new motor arrives next week. 3 women in the house I can’t go a day without a dryer. Thanks again

Where is AC relay on 04 Sentra 1.8

I recently had to replace the belt and tried several tools to try to leverage the belt up onto the backside of the wheel, as suggested in this video, but the space was very limited. I was finally able to complete the task by immersing the new belt in boiling water, for about 5 minutes, to give it more pliability. To guide it up onto the wheel, I used a very firm rubber door stop, which forced it up, and onto the wheel. Hope that helps others.

Wish I could get R12 in Germany. Impossible

Hello, I'm not sure if you will see this message but do you happen to know how to activate the camera lens?

oh and btw its a singer 640 touch and sew.

I know this is an older video and hopefully you will answer (crosses fingers) but its helped me except I cannot get the top upper vertical gear out... it has the smallest allen wrench screw I've ever seen..and they are stuck in there... i don't understand how to get it out..its so frustrating. This is for a customer of mine. I own a restoration sewing machine shop and I bought a new gear..now I've followed your video and that top gear just wont budge.what do you suggest? Please help thank you

I hate led

engine balance shaft bad!

It is bad engine balance shaft ! I have 2011 camry It have the same sound lik this.

The ingenious way of alignment for metal blades. I have a windmill ant the blades were out of alinement. Worked great. Thanks

I like too 😏

SORRY, dude, but that was a waste of time. all you did was R&R the fuel line. No testing of any fuel pressure. Might want to retitle your video.

Thanks a lot for this video! I just got a 06' Maxima & been searching for solutions to fix the clutch issue.

Says nothing helpful. Trying to find how to light my dryer. Purpose of video is unclear

Thank You for this video. I am very attached to my Singer Touch & Sew for 57 years. I don't know if I could function without it:) I hope the local sewing repair shop will be willing to fix, if not then I will make an attempt:)

Hey Nick do you still have the same number I've tried to call you and I text you but I never hear back

Where did you get the lines that connect the Master to the slave cylinder?

I am rebuilding a 2ARFE engine for my Toyota RAV4. The top timing chain guide bolt had loosened itself and fallen out, eventually causing the guide to break and the chain to break. Which, damaged the crankshaft reluctor wheel and required full rebuild of engine. If you are still having this problem, I would recommend it getting looked at ASAP. It appeared that the bolt took some time to come out as it wore down the threads in the block. I bought the car from a friend after it died, so I don’t know if it had this rattle before, but I can only assume that there was some rattle that led up to the chain breaking.

Glad I found this video. An Amazon Canada seller has the exact replacement part for $130 This is doable and saves our family hundreds of dollars!

Thank you for posting the videos on repairing a Maytag dryer. I have watched them repeatedly.

What size wrench did you use for the brake line

How to adjust yellow flame 😢?

Have you checked under the engine? If this noise is louder near the oil pan, could be a faulty balancer shaft.

Does the center wheel that the bobbin sits directly on need any special alignment? I have done the hook timing, but the bobbin keeps getting fouled with the thread. I know that I moved this "bobbin turntable" when I replaced the bobbin gear directly below it.Thanks.

Whats the ohms?

I opened mine up and to my surprise there was no filter in there.

Is there anything internally that I would need to mod or just use an oil separator to return the oil??..I actually have one of these and want to use it on the engine of my service truck for a back up air source but can’t find any info on how to use it as a air compressor…any tips would be appreciated Thanks for the video!

This is cool . I would spray paint the inside of the covers silver or put aluminum tape, Place them at 45 degree angle to reflect more light onto the ceiling.

Late to this but I have the same exact problem. Still trying to diagnose it but I would highly recommend taking a look at possibly a timing chain issue

If my truck has no muffler, will it break down eventually, leaving me stranded?

Did the exact same thing you did on you video only difference my dryer motor made a horrid humm no spinning .Would only start spinning if I turned it by hand would start turning very very slowly and up to speed no factory connection for start circuit.

I’m doing this today because I got the parts in. My drum was grinding metal on metal! It looks like the last owner put the cork on top and the nylon underneath… no wonder it failed haha

Amazing lights

Where exactly can you find the fuel filter on the 06 Sentra?

1:27 a car after eating a Taco Bell bean burrito

Mine was noisy I assumed it was a roller bearing but it is more like a bushing really

ruclips.net/video/quL_gmUXe4I/видео.html

I noticed the inducer wheel was spinning freely. Mine does the same but won't start, should I replace the entire inducer assembly?

This sounds like Jeff Lynne's beautiful and unique vocals.

What was wrong with them that you had to put new ones on?? Can they warp or something? I took a strip of fine sand paper and sanded mine (did not remove them),then a tad bit of high-temp grease and that fixed the squeaking...

Am I buggin or did bro rip ass @2:09 ?

I'm a 50 year handyman, but you saved me like $380 sir!